Blog

Digital load cell amplifiers are also called weighing transmitters. It can convert physical quantities into electrical signals, and convert the sensors outputting millivolt signals into standard DC signals through isolation and amplification. It usually adopts SMT process and is designed and manufactured for resistance strain signal sensors in industrial processes, and is suitable for load cells of different specifications.

Relays are an electronic control device with a control system (that is, an input loop) and a controlled system (output loop), and are usually used in automated control circuits. The relay is actually an "automatic switch" that uses a small current to control the operation of a large current. It plays the role of conversion circuit, automatic adjustment and safety protection in the circuit.

Toroidal transformer is a large type of electronic transformer and has been widely used in home appliances and other electronic equipment with high technical requirements. Its main use is as a power transformer and an isolation transformer.Toroidal transformers have been widely used in electronic equipment with
high technical requirements such as computers, medical equipment, telecommunications, and instruments.

A variable frequency drive (VFD) is a type of motor controller that drives an electric motor by varying the frequency and voltage of its power supply. The VFD also has the capacity to control ramp-up and ramp-down of the motor during start or stop, respectively. Even though the drive controls the frequency and voltage of power supplied to the motor, we often refer to this as speed control, since the result is an adjustment of motor speed. In this article, we will test VFD constant pressure water supply system.

UPS is an uninterruptible power supply with energy storage device. It is mainly used to provide uninterrupted power supply to some devices that require high power stability. When the mains input is normal, the UPS will stabilize the mains and supply it to the load. At this time, the UPS is an AC voltage stabilizer, and it also charges the battery inside the machine; when the mains is interrupted (accidental power failure) When the UPS is switched on, the UPS will immediately supply 220V AC power to the load by switching the DC power of the battery to the load, so that the load can maintain normal operation and protect the software and hardware of the load from damage. UPS devices usually provide protection against overvoltage or undervoltage.

Alternating current power is a form of electricity in which power flows constantly in changing directions. Since the early 19th century, AC is the form of power that has been used in homes and businesses. However, for most businesses and industries, three phase AC power provided by single phase to three phase converters is used because it accommodates higher power loads. Three phase power consists of 3 power wires and each one of them is 120 degrees out of phase with each other.

There are many types of air compressors. According to different standards, air compressors can be divided into different types. Today, we will introduce a kind of air compressor—screw compressor in detail.

The proximity sensor is a general term for sensors that replace contact detection methods such as limit switches and are designed to detect without touching the detection object. It detects the movement and presence of objects and converts them into electrical signals. The principle of PNP and NPN sensors is to use the saturation and cut-off of triodes to output two states, which belong to switch sensors, but the output signals are diametrically opposite. high level and low level. NPN output is low level 0, and PNP output is high level 1.

The principle of hipot tester is to apply a voltage higher than normal working voltage to the insulator of the device under test for a specified period of time. If the insulation is good enough, the voltage applied to it will only produce a small leakage current. If a device maintains its leakage current within the specified range for a specified period of time, it can be determined that the device under test can operate safely under normal operating conditions. This article will introduce safe operation of hipot tester.

Programmable relay stores some typical relay logic control program in internal memory in advance and realize some simple logic control and sequence control function by the user program combination and calls. Its integrated internal software function and programming software can replace the traditional relay logic circuit, such as the logic circuit composed of relay, contactor and timer, and has a strong anti-interference ability. Therefore, programmable relay is widely used in industrial automation control system, small machinery and devices, building electrical and other fields. It is applicable to the control of intelligent residence system, lighting system, heating and ventilation system, door, window, fence and moving door.

The torque sensor calibration device is divided into two categories: dynamic and static. Dynamic torque sensors can also be called torque sensors, torque-speed sensors, non-contact torque sensors, and rotational torque sensors. Torque sensors are the detection of torsional torque sensing on various rotating or non-rotating mechanical components. ATO torque sensors convert physical changes in torque into precise electrical signals. It can be used in the manufacture of viscometers and electric (pneumatic, hydraulic) torque wrenches, with the advantages of high precision, fast frequency response, good reliability and long life.

Economy linear stepper motor is a stepper motor with lead screw, this stepper motor can be used in many high-precision requirements including precision calibration, precision fluid measurement, and precise positional movement, it can directly move linearly, which can make the machine miniaturized. The step size of the linear stepper motor is determined by the step angle of the motor and the pitch of the internally threaded nut and the lead screw. In order to ensure high working efficiency, there must be a certain degree of freedom between the rotor and the lead screw, which requires a certain gap between the two, which is about 0.03 to 0.08 mm backlash.

HMI, short for human machine interface, is a medium for interaction and information exchange between systems and users, which realizes the conversion between the internal form of information and the form acceptable to humans. Human-machine interfaces exist in all fields that participate in the exchange of human-machine information. So, how do HMI and PLC control VFD?

Variable frequency drive (VFD) is a power control device that uses frequency conversion technology and microelectronics technology to control the AC motor by changing the frequency of the motor's working power supply. The variable frequency drive is mainly composed of rectification, filtering, inverter, braking unit, driving unit, detection unit and micro-processing unit. It adjusts the voltage and frequency of the output power supply by switching on and off the internal IGBT, and provides the required power supply voltage according to the actual needs of the motor, thereby achieving the purpose of energy saving and speed regulation. In addition, the VFD has many protection functions, such as overcurrent, overvoltage and overload protection, etc. Now, we will talk about ATO VFD analog output setting and wiring.

A programmable logic controller (PLC) or programmable controller is an industrial computer that has been ruggedized and adapted for the control of manufacturing processes, such as assembly lines, machines, robotic devices, or any activity that requires high reliability, ease of programming, and process fault diagnosis. PLCs were first developed in the automobile manufacturing industry to provide flexible, rugged and easily programmable controllers to replace hard-wired relay logic systems. In this article, we will introduce the counter function of PLC.

A stepper motor is a motor that converts electrical pulse signals into corresponding angular displacement or linear displacement. Each time a pulse signal is an input, the rotor rotates an angle or moves forward one step, the angular displacement or linear displacement it outputs is proportional to the number of input pulses, and the rotational speed is proportional to the pulse frequency. Therefore, the ATO stepper motor is also called a pulse motor.

Do garage door openers have power? Insert a light into the socket. If the light does not come on, check the fuse box or circuit breaker. Are all doors unlocked? Re-read the installation instructions warnings. Is there ice or snow under the door? The door may have frozen to the ground. Clear obstacles. The garage door spring may have broken. Ask a qualified person to replace it.

An automatic transfer switch (ATS) is a device that automatically transfers a power supply from its primary source to a backup source when it senses a failure or outage in the primary source. When a failure occurs in a primary power system, the ATS invokes a standby power source, such as an uninterruptable power supply. An ATS can also start up more long-term backup power systems, such as local diesel generators, to run electric equipment until utility power is restored.

CNC router machine is an automatic processing equipment developed on the basis of general milling machines. The processing technology of the two is basically the same, and the structure is also somewhat similar. CNC milling machines are divided into two categories: without tool magazine and with tool magazine. Among them, the CNC milling machine with a tool magazine is also called a machining center.

The transmitter is a device that converts physical measurement signals or ordinary electrical signals into standard electrical signals (4~20mA, 0~20mA, 1~5V, 0~ 10V, etc.) output or can be output by communication protocol (CANBUS, MODBUS, PROFIBUS, etc.) ATO offers high-performance current transmitters, level transmitters, voltage transmitters, temperature transmitters, load cell transmitters, pressure transmitters, temperature and humidity transmitters, and PH transmitters.